ASTM F2164 PDF

An American National StandardDesignation: F – 02 Standard Practice for Field Leak Testing of Polyethylene (PE) Pressure P. described in ASTM F, “Standard Practice for. Field Leak Testing of Polyethylene (PE) and. Crosslinked Polyethylene (PEX) Pressure Piping. Systems Using. As a similar alternate, ASTM F instructs to fill and then thermally stabilize the pipeline with no air entrapment, pressurize the pipeline at test pressure for.

Author: Kazisar Gojora
Country: Azerbaijan
Language: English (Spanish)
Genre: Health and Food
Published (Last): 27 October 2017
Pages: 187
PDF File Size: 15.36 Mb
ePub File Size: 6.14 Mb
ISBN: 982-8-67413-362-3
Downloads: 72500
Price: Free* [*Free Regsitration Required]
Uploader: Meztilabar

Work Item s – proposed revisions of this astm f2164. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Additional safety information is presented in Section 7 and throughout this standard.

ASTM F2164 – 13

Under test pressure, piping materials astm f2164 expand slightly in diameter and contract in length slightly according to the Poisson ratio of the material. Poisson-effect length reduction may affect or cause disjoining in other contiguous sections that astm f2164 partially restrained or non-restrained joints, such as bell-and-spigot joints, when such joints are in-line with the test section.

It is the responsibility of the astm f2164 of this standard to establish appropriate safety and health practices and determine the applicability of asstm limitations prior to use. It is the astm f2164 of the user astm f2164 this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Contact the joint or connection manufacturer for information.

For safety reasons, some manufacturers prohibit or restrict pneumatic pressure testing of their products. For safety reasons, some manufacturers prohibit or restrict pneumatic pressure testing of their awtm. Contact sstm manufacturers for information about testing with gas astm f2164 pressure. Link to Active This link will always route to the current Active version of the standard.

Related Posts  STANAG 4159 DOWNLOAD

Contact component manufacturers for information about testing with gas under pressure. Active view current version of standard. In a compressed gas test, both the pressure stress on the astm f2164 and the energy used to compress the gas are released at a failure.

See also Test Method F Note 2 — When a tensile stress is applied to a material, it will elongate in the direction of the applied stress, and will decrease in dimension at astm f2164 angles to the direction of the applied stress.

In a compressed gas test, both the pressure stress on the system and the energy used to compress the gas are released astm f2164 a failure. Such systems may contain lower pressure rated or non-pressure rated components that cannot be astm f2164 from test pressure, or temporary caps or closures may not be practical.

The ratio of decrease to elongation is the Poisson ratio. It does not verify if a piping material or a piping system design is suitable for pressure service.

To prevent Poisson-effect disjoining, take measures such as the installation of external joint restraints diametrical clamps and tie-rods on in-line non-restrained joints, installing in-line thrust anchors at the ends of the fully restrained section, or isolating the fully restrained test section from piping with non-restrained or partially restrained joints. astm f2164

For field-testing of plastic gravity flow sewer lines, see Test Method F In the test phase, expansion is suspended by slightly reducing test pressure. In these systems, leak inspections astm f2164 be conducted during and after installation.

Related Posts  CSA W47.1 EPUB

To compensate for expansion, make-up astm f2164 is added during the initial expansion phase. The amount of make-up water expansion allowance will vary because expansion is not linear.

This procedure compensates for expansion with an astm f2164 expansion phase, followed by a test phase. For field-testing of plastic gravity flow sewer lines, see Test Method F Leakage or faults usually occur at connections, joints, and mechanical seals astm f2164 sealing under pressure is required.

Failure during a pressure leak test can be explosive, violent, and dangerous, especially if a astm f2164 gas is used. Failure during a pressure leak test can be explosive, violent, and dangerous, especially if a compressed gas is used.

ASTM International – Standard References for ASTM F – 13

Astm f2164 —Safety is of paramount importance when conducting hydrostatic pressure leak tests because testing under pressure may cause sudden violent rupture or failure. Link to Active This link will always route to the current Active version of the standard.

Historical Version s – view previous versions of standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Work Item s – proposed revisions of this standard. Referenced Documents purchase astm f2164 The documents listed below are astm f2164 within the subject standard but are not wstm as part of the standard.